How to choose a good electric boiler: what should you look out for before buying?

Loading

Contents

The boiler is a vital component of a heating system, on which the efficiency of its operation depends. At present, hot-water heating is one of the most common types of heating, which explains the growing popularity of hot-water boilers.

You will find a variety of units on sale, which differ in terms of the coolant used, design, installation technology, etc.

Purpose

A hot-water boiler is used to heat small buildings, cottages and townhouses. Such units are typically used where there is no central heating system, or in situations where it is not practical to install a boiler room. As well as for heating, they are used in hot water supply systems.

A hot-water boiler is a device designed to heat water under pressure, i.e. without allowing it to boil.

Device specifications and operation

At the heart of almost every electric boiler is a heating element. It consists of internal heating elements, which are switched on by automatic control units. These elements heat the heat transfer fluid, which then transfers heat to the heating circuit. Electricity is supplied from single-phase and three-phase mains supplies. The efficiency of electric boilers is such that they convert electrical energy into heat almost entirely: the efficiency of the units is close to 99 per cent.

Animal repellents Non-destructive
deterrence of
rodents,
wildlife
and snakes.

Conventional boilers are characterised by their compact size, which means they do not take up space in the living area. However, this does not solve the problem of a shortage of hot water. As you know, only flats in multi-storey blocks in towns and cities have a centralised hot water supply.

For those living in rural cottages, there is the option of heating water manually or using an electric instantaneous or storage water heater. Dual-circuit electric boilers for heating a house are not much more complicated than their single-circuit counterparts. At the same time, they are capable of heating water via an additional heat exchanger with heating elements.

This design consists of the following elements:

  • Two radiators.
  • Expansion tank.
  • Safety assembly (sometimes replaced by a safety valve).
  • Circulation pump.

The heating circuit for the main heating element is switched on according to the set temperature settings. In this case, the heating element for the DHW circuit is only activated once the hot water tap has been turned on. As for other types of internal layout for dual-circuit boilers, these have not gained a foothold in the plumbing equipment market due to their imperfect design and numerous weaknesses. In one such design, the water in the DHW circuit is heated by the heating circuit.

Electric dual-circuit boilers for heating and hot water supply are divided into two groups according to the type of installation:

  • Wall-mounted.
  • Outside.

Floor-mounted models are characterised by higher output: for this reason, they are used to heat large homes. There is no need to worry about losing living space, as they take up little room and are compact. In a small home, it is recommended to use compact wall-mounted electric boilers for heating and hot water. Some models of this type offer good output, which is sufficient for heating large areas.

A new development on the boiler market is the so-called ‘energy-efficient’ dual-circuit electric boilers for heating private homes. Their design incorporates innovative features. These units include ‘Scorpion’-type electrode boilers. Thanks to their automated controls, it is possible to heat a home quickly and cost-effectively. A key feature of induction appliances is their safety and long service life.

Heat transfer fluid temperature

Specify the nominal and minimum water inlet temperatures for the boiler. The nominal temperature is the temperature that the unit must deliver under normal operating conditions. It usually ranges from 60 to 110 °C.

A minimum temperature must be maintained to prevent low-temperature corrosion of the pipework caused by the formation of condensation inside it.

The maximum outlet temperature from the boiler is the temperature at which the heat transfer fluid does not boil. This is usually 110–115 °C.

A unit with this rating is intended for individual use. However, there are also products with a higher maximum temperature rating. These are used in thermal power stations.

Gradient. This refers to the temperature difference between the water entering and leaving the boiler. It is usually between 50 and 55 °C. The gradient value is influenced by the material from which the appliance is made.

Boilers with flame tube heat exchangers

These hot-water gas boilers are designed to ensure that the incandescent combustion products move through special channels known as fire tubes or flue gas channels. The duct assemblies are cooled from all sides by a circulating coolant, which extracts heat from them. At the same time, depending on the design, the flue gases pass through the pipework twice or three times in both forward and reverse directions. Accordingly, heaters with such heat exchangers are referred to as two-pass or three-pass. We shall consider the design and operating principle using the example of a heat generator with three passes for combustion products.

  • A – external thermal insulation layer;
  • B – second-stage gas channels;
  • C – furnace working area;
  • D – control unit (controller);
  • E – thermally insulated entrance doors;
  • F – cross-section of the first-stage flue tubes;
  • G – cast-iron firebox ribs for improved heat transfer;
  • H – heat channels of the third course.

This type of unit is a dual-fuel model and can run on either methane or diesel; switching between fuels simply involves replacing the burner. When using methane, the gas-fired hot-water boiler operates as follows: a modulating burner located inside the furnace produces a flame that heats the cast-iron fins and the entire surface of the primary gas channels.

Air is forced into the working chamber by a fan and enters the burner assembly. However, a single blower is not sufficient for the combustion products to successfully overcome the resistance of the three sections of flame tubes. A second fan – a flue gas extractor – is therefore fitted at the end of the air duct, at the start of the external flue. As a result, the maximum temperature of the combustion products at the outlet of the hot-water heat exchanger is 180 °C, and fuel combustion efficiency ranges from 88 to 94 per cent.

Thanks to their design, three-pipe heating systems offer considerable efficiency compared with the heaters previously considered. They are favoured by owners of large holiday homes or industrial buildings. For the same reason, the system does not have a secondary circuit for hot water supply, whereas in previous types of hot-water installations it is possible to install a secondary heat exchanger for hot water supply.

Advertisements

Every methane gas water heater is designed to meet specific operating conditions. Conventional units are mainly manufactured in an energy-independent design and are intended for domestic use, i.e. for heating private houses or flats. Condensing boilers are more versatile, as they cover a wide range of outputs, with some models delivering up to 1.5 MW. Two- and three-way installations are not suited to heating systems in small buildings; their initial heat output ranges from 80 to 100 kW.

Varieties

Modern hot-water boilers are generally constructed in much the same way. They may vary depending on the manufacturer (domestic or foreign) and their performance characteristics.

Speaking of the design, all the boilers are split-type.

Dignity

One of the main advantages of a gas-fired unit is its ability to switch to liquid fuel, which may be necessary in the event of an emergency shutdown of the gas pipeline.

Nor should we overlook its operational safety. This is ensured by a built-in flame sensor, which cuts off the power supply should the flame go out. The hot-water boiler is supplied with a thermostat, so the system is protected against emergencies should the water temperature rise to a critical level.

The gas pressure in the system is monitored by safety electronics, as low pressure levels cause the boiler to shut down. Following the same principle, the operation of the unit is adjusted in the event of a power cut; when the power is cut off, the gas supply valve closes.

Modern appliances are capable of responding to changes in air temperature readings; therefore, the heating stops once the set temperature is reached and resumes when the temperature drops.

Recommendations

The following rules apply to the operation of hot-water boilers:

  • A hot-water boiler requires regular inspections and adjustments, which must be carried out by a qualified technician.
  • The boiler system should be installed and commissioned by a qualified professional.
  • The boiler must be serviced every three years.

Installation

In view of their output, dimensions and intensive operating regime, industrial hot-water boilers are installed only in annexes or separate buildings. As an exception, they may be installed in a building’s basement, provided all requirements for a boiler room are met. It is prohibited to install specialised heat generators in production areas (workshops).
Almost all industrial boilers are designed for floor installation. In recent years, however, compact, high-output wall-mounted models have appeared on the market. These new models are more convenient, although, given their weight, there is a restriction: they are only suitable for rooms in buildings constructed from durable materials. They are not suitable for installation in lightweight extensions, timber-framed structures or even brick-built structures. Only reinforced concrete walls are capable of withstanding such loads. Alternatively, a special metal frame structure can be constructed to secure the heating appliance.

One of the characteristics of industrial hot-water boiler installations is the need for reserve capacity. Should problems arise with the water supply system, it will be necessary to organise a supply of liquid from it to top up the system – the production cycle cannot be halted.

How does a hot-water electric boiler work?

  1. Indirect heating.
  2. Direct effect on the coolant.

How is the heating medium supplied?

  • Indirect heating – this operating principle is used in heating elements and induction models. In the tank, the heater is in contact with the surface of the coolant. Under the influence of electricity, the surface of the heating element or induction rod heats up. The heat is transferred to the heat transfer fluid, which surrounds the surface of the heater on all sides. The principle of indirect heating is inefficient. A large amount of thermal energy is expended on heating the heating element and is lost during heat transfer. It takes about 10 minutes for the heater to reach operating power after being switched on.
  • Direct heating is the operating principle that distinguishes electrode electric boilers. The method essentially involves the direct application of an electric current to the coolant. To ensure the required heating intensity, a large amount of salt is added to the heating system’s coolant. Although the coolant can be produced independently, it is recommended to fill the heating system with a special factory-made formulation. Twice a year, you will need to bleed the air from the heating system, which is produced as a result of the coolant being directly exposed to an electric current.

All boilers operating on the principle of indirect or direct heating are classified as instantaneous water heaters for individual heating systems. Continuous circulation of the coolant is essential for successful and efficient operation.

Pressure in the boiler is generated naturally and by forced circulation. A circulation pump is fitted to the boiler unit with a heating element, which ensures the necessary circulation of the coolant within the heating system. Electrode boilers operate on the principle of natural circulation, but if necessary, a pump may be fitted to the return pipe of the heating circuit.

Hot water supply

  • Boilers with heating elements – some modern models of electric boilers that use a tubular heater have two circuits: one for heating the coolant and one for connecting to the hot water supply. An additional heating element has been incorporated into the boiler’s design. When you turn on the hot water tap, a signal sounds to switch on the heating element. Hot water begins to flow after a few seconds.
  • Induction and electrode boilers – this equipment does not allow for the connection of a domestic hot water system. If hot water is required, an indirect heating boiler is installed, which is connected to the heating system.

In terms of energy efficiency, double-circuit heating elements are significantly less efficient than systems using an indirect heating boiler.

Features of the heating system

An electric boiler is a suitable option for heating a house. If the house is not used as a permanent residence, it makes sense to use antifreeze instead of water as the heat transfer medium. This measure will prevent the pipes from bursting in the event of an emergency shutdown of the heating system due to a power cut.

Thanks to the thermal insulation of the casing, the circulating coolant does not cool down immediately, so short-term power cuts do not affect the system’s operation. However, it is impossible to keep the coolant hot for long whilst the power is off.

Please advise! Antifreeze, a 50 per cent ethanol solution or a 70 per cent glycerine solution can be used as a heat transfer fluid. These liquids will not freeze, even if the temperature drops to 30–40 degrees below zero.

When installing an electric heating system, a separate connection with its own fuses must be provided. However, this is not necessary when installing a boiler, as this appliance is connected to the main circuit because its power rating is low.

Electric boilers are therefore the best choice for areas without a gas supply. Such a system can be used for both heating and hot water supply. The heating system is characterised by its ease of use, environmental safety and relatively high efficiency.

Advertisements

Choosing the right type of instantaneous water heater

When choosing an instantaneous water heater for a bathroom, kitchen or country house, four main factors are taken into account: the type of control, the availability of additional features, capacity and output.

The budget models only offer basic options. In the advanced settings, you will find the following features:

  1. Thermal cut-out. A sensor that prevents heat build-up can extend the appliance’s lifespan and protect the user from burns.
  2. Child lock. This function prevents children from using the appliance, but it can be replaced by a temperature limit.
  3. A high-precision temperature sensor. A useful feature that allows you to set the heating to a precise level. It is particularly important when the water pressure is unstable.
  4. Economy mode. During prolonged use, the heater automatically reduces the water temperature.
  5. Remote control. Allows you to switch between modes remotely.

It is strongly recommended that you consider the level of electrical safety. Some models may even fail due to steam.

An important criterion is the type of control system. The difference is not just in the price: hydraulic systems have a number of limitations.

  1. Mechanically operated appliances always start at maximum power, even if the user has set a specific mode beforehand. This may cause burns.
  2. Another disadvantage is the fixed temperature difference. This is usually 25 °C. If ice-cold water (+5 °C) is supplied in winter, the output will be cool water (+30 °C). This is sufficient for washing your hands, but not for showering.

The cost of electronically controlled appliances is due to the inclusion of additional sensors, a microchip and heating elements with multi-stage power control.

Not only do they add a wide range of options, but they also offer flexible functionality.

When choosing a pressure device, those with an eye for aesthetics should pay attention to the appearance of the body.

Selection based on water consumption and performance

When calculating power, you should take your own goals and needs into account.

If the heater is to be placed in the kitchen and used to provide water for washing up, 2–4 litres per minute will be sufficient.

For a bath, you’ll need a more powerful unit – 8–10 l/min.

A water heater for a shower cubicle must have a capacity of 4–8 l/min.

If the appliance is to serve several rooms at the same time, you should select the flow rate for the room with the highest water consumption and multiply it by 1.5.

By the power of

The head (indirectly) and the heating output depend on the unit’s power. It is more difficult to calculate this parameter, as the temperature of the water supplied may vary.

Furthermore, +40 °C is considered a comfortable temperature for a shower, and +55 °C for a kitchen sink. This is important for disinfection and removing grease.

With a power output of 3.5 kW, you’ll be able to have a shower in the summer, but the water flow will be weak.

In winter, a flow-through water heater of this type cannot cope with the task, as the temperature of the incoming liquid at the inlet will be much lower. The difference is as much as 20°C.

5–7 kW is still not enough for comfort, but the water heater will be able to provide backup in most emergency situations.

In cold rooms, the appliance cannot cope with the heating in winter.

Electric water heaters with a power output of over 12 kW are suitable for solving any problems.

However, if several points need to be served simultaneously, it is better to opt for more efficient models – from 20 kW upwards.

Common mistakes when choosing

  1. Purchasing an instantaneous water heater without temperature control or sensors. In the event of a leak, this budget model could cause burns to the user.
  2. Purchasing equipment without first consulting an electrician. You must select a separate circuit for the installation. The main factor to consider is the power allocation for households. In older buildings with 16 A sockets, it is not possible to install appliances with a power rating exceeding 3.5 kW. In new-builds with 32–40 A circuits, a further limit of 6 kW applies.
  3. Failure to take operating pressure into account. If the pressure is low, the sensors on some models will not respond to the water supply. Most appliances operate at 0.5 bar, but this point needs to be clarified.

Classification by operating principle

Its functionality depends on the type of appliance. For example, you can take a portable water heater with a shower head with you when travelling, but such appliances have low output and are unable to provide a comfortable water pressure.

Gravity-fed instantaneous water heaters

Non-pressurised units are fitted with a separate shower head and are connected to a single outlet.

This option may be suitable for a summer residence or in the event of an accident.

Non-pressurised electric direct-current water heaters operate only with the nozzles included in the complete set.

It is important to bear this in mind, as once it is installed, you will have two jugs: one from the blender and one from the appliance.

Electric instantaneous water heater

Pressurised appliances are more convenient and versatile.

Instantaneous shower water heaters can be connected to a single tap or to a riser pipe.

This enables hot water to be used throughout the house.

The cost of such equipment is higher, so it is advisable to purchase it for frequent or regular use.

For maximum comfort, you should choose an electronically controlled instantaneous water heater.

Hydraulic models are less versatile, so they are not suitable for everyone.

It is recommended that you install a separate filter in advance, as the built-in ones are not entirely up to the task.

The cost of pressure equipment is relatively high (from 10,000), so it is advisable to take steps to ensure its longevity in advance.

The strengths and weaknesses of electric dual-circuit boilers

Electric dual-circuit domestic boilers are characterised by their exceptional convenience and practicality. As a result, owners of country homes no longer need to organise their hot water supply.

The advantages of the equipment are as follows:

  • Compactness … In terms of size, electric dual-circuit boilers are significantly larger than gas heaters.
  • No noise … The equipment operates without any rumbling or noise, which means it can be installed in any room.
  • Environmentally friendly … No harmful substances or carbon dioxide are released during operation.
  • Speed of installation … During installation, you spend less time fiddling about with pipes and other components.
  • Fire safety … There is no risk of gas leaks, fire or explosion.
  • Easy to use … All you need to do is dust off the igniter from time to time.
  • It can be installed anywhere … In this case, no special boiler room is required: the unit can be installed in the kitchen, in a cupboard or in the basement.
  • High efficiency (almost 99 per cent).
  • The option of using 220 V and 380 V mains supplies … The output of the boiler used is of crucial importance.

The disadvantages of dual-circuit electric boilers for domestic heating are usually:

  • If you wish to connect a high-power appliance, you will need to install a separate circuit. This primarily applies to boilers with a power rating of over 3 kW. The supply point for such a circuit is a standard electrical distribution board.
  • Expensive compared to gas or solid-fuel units.
  • High electricity consumption when the circuits are all switched on at the same time. For this reason, a separate electrical circuit is required.
  • High costs for electricity consumption. As you know, electricity is by no means cheap.

The disadvantages mentioned are not critical, particularly in situations where dual-circuit electric boilers are the only option for heating residential premises and providing hot water. This applies in particular to areas where there is no gasification and no stable supply of solid fuel.

Solid fuel boilers

This type of boiler is popular with homeowners. It is used for heating in rural areas or in places where firewood, pellets or coal are cheap and readily available.

Pellet-fired water heater

  • Type of fuel. Wood – either logs or pellets – and coal are used as fuel. There are also multi-fuel boilers with several combustion chambers.
  • Fuel combustion method. Available in standard, slow-burn and pyrolysis modes.

Pellet models are particularly popular, as they offer a high level of automation with long-term programming of operating modes. These are the most advanced fuel-fired water heaters in the solid fuel range.

In a traditional solid-fuel boiler, heat is generated simply by burning wood, just as in a wood-burning stove. This gives rise to all the disadvantages of such units – they will need to be cleaned, the flue gas flow monitored, firewood constantly added, and the intensity of combustion and draught regulated using a damper, etc. There is, in principle, no question of any autonomy. Efficiency does not exceed 75 per cent. The advantages lie in reliability, the simplicity of the design and pipework layout, independence from electricity, and low costs.

Water heaters with long-burn or top-burn combustion use a different method of feeding fuel – from the top. As a result, the fuel burns out completely and efficiency is improved.

Pyrolysis boiler plant

Advertisements
AliExpress

Leave a Reply

Your email address will not be published. Required fields are marked *